Tilta Nucleus-Nano Micro USB to USB-C Nano Motor Power Cable Subtotal: $58.00
Camera & Vision
Showing 6016–6030 of 6353 results
-
Lens control systems
Tilta Nucleus-M Follow Focus marking Disk (x1)
This follow focus marking disk attaches to the hand wheel of the FIZ hand unit to allow you to create drawn-on custom marks for accurate focus pulls.
1. (1) Tilta Nucleus-M Follow Focus Marking Disk
Color: White
Materials: ABS plasticSKU: TIL-WLC-T03-MD-1 -
Lens control systems
Tilta Nucleus-M II Wireless Follow Focus System
Coming soon!
- 4-Channel Focus, Iris, Zoom & ND Control
- 2.4″ Touchscreen, Electronic Focus Ring
- Reliable & Fast 0.02-Second Response
- Handwheel, Right & Left Handgrips
- Two Lens Drive Motors, 15 & 19mm Mounts
- Use Handwheel on Right or Left Side
- Dedicated Interference-Resistant Channel
- Two 0.8 MOD & One 0.5 MOD Drive Gears
- 128 Lens Data Presets with Hand Unit
- MARK Point & RANG Memory Protection
SKU: TIL-WLC-T06 -
Lens control systems
Tilta Nucleus-M Motor Kit 1
This Nucleus-M motor kit allows you to add a motor to your Nucleus-M kit along with the 7-pin to 7-pin power cable that allows you to power the motor from a daisy-chained connection to another Nucleus-M motor.
Color: Tilta Gray
Materials: Aluminum-alloy, stainless steelSKU: TIL-WLC-T03-M1 -
Lens control systems
Tilta Nucleus-M P-TAP to 7-Pin Motor Power Cable
This P-tap to 7-pin cable for the Nucleus-M allows you to power the motors from a P-tap power output port. Simply plug this cable into one of the motors and then daisy chain power to the other motors using the Nucleus-M 7-pin to 7-pin power cables.
Weight: 0.08 lbs
Length: 76.8 cm
Color: Black
Materials: ABS plastic, copper, rubber, aluminum-alloySKU: TIL-WLC-T03-PTAP-7P -
Lens control systems
Tilta Nucleus-M Wireless Lens Control System Partial Kit I AU plug without batteries
Lens control systemsTilta Nucleus-M Wireless Lens Control System Partial Kit I AU plug without batteries
It allows you to have full control of focus, iris, and zoom on either the FIZ hand unit or between the two wireless hand grips. You can even split control of the channels between the hand unit and wireless hand grips as you see fit with the push of a button.
The wireless range of both the hand unit and hand grips is 1,000 feet.
The hand grips can be attached to the included rosette mounts for handheld operation and can also be attached to top bar-based gimbals with the included Nucleus-M Hand Grip to Gimbal Adapters or to ring-based gimbals with the optional Nucleus-M Hand Grip Universal Gimbal Ring Adapters.
Each motor has its own built-in motor drive that communicates directly with the hand unit and hand grips. This negates the need to mount a separate MDR to your rig, allowing for a more compact camera setup and a quicker setup time.
Simply set the motors and hand unit/hand grips to the same channel and you will have full control.
The motors allow for automatic calibration of the lens as well as manual calibration if you are using lenses that don’t have hard end stops at close focus and infinity.
The motors are designed to clamp onto 19mm or 15mm rods (with the included rod bushings). This clamp-on design allows you to easily attach and detach the motors without needing to remove any other accessory from your setup.
Every motor has a 0.8 mod, 35 tooth, 32 pitch gear attached, which is the standard gear size for cinema lenses. The torque of the Nucleus-M Motor at 14.8V is 2.5N·m
To power the motors, only one power port on your camera rig needs to be used. Simply plug the P-tap power cable into one of the motors and then daisy chain power to the rest of the motors with the short 7-pin to 7-pin cables.
The motors can be powered through a power source that has a voltage output ranging from 7.2V-24V.
The hand unit and hand grips are each powered with two 18650 rechargeable batteries (batteries NOT included). When fully charged, the batteries in the hand grips last up to 2 days, while in the hand unit they last up to 10 hours.
Remote start/stop is possible by plugging a compatible Nucleus-M R/S cable into the open 7-pin port of a motor. This then gives you R/S capabilities through the hand unit and/or the handles.
** PLEASE NOTE: The R/S cables we offer for our wooden handles ARE NOT compatible with the Nucleus-M since the engineering and pin configurations are completely different. Using the wooden handle R/S cables are not safe to use with the Nucleus-M.
Only use cables that have been developed by us exclusively for the Nucleus-M system.
Weight:
Motor Dimensions:
Material: Aluminum-alloy, stainless steel, ABS plastic, rubber, Brazilian rosewood
Color: Tilta Gray
Recommended Battery Link: https://tilta.com/support/which-batteries-do-you-recommend-for-the-g2-g2x/
Tiltamax Nucleus-M Firmware Update 18.12.19 – December 2018SKU: TIL-WLC-T03-K1 -
Lens control systems
Tilta Nucleus-M Wireless Lens Control System Partial Kit IV AU plug without batteries
Lens control systemsTilta Nucleus-M Wireless Lens Control System Partial Kit IV AU plug without batteries
It allows you to have full control of focus, iris, and zoom on either the FIZ hand unit or between the two wireless hand grips. You can even split control of the channels between the hand unit and wireless hand grips as you see fit with the push of a button.
The wireless range of both the hand unit and hand grips is 1,000 feet.
The hand grips can be attached to the included rosette mounts for handheld operation and can also be attached to top bar-based gimbals with the included Nucleus-M Hand Grip to Gimbal Adapters or to ring-based gimbals with the optional Nucleus-M Hand Grip Universal Gimbal Ring Adapters.
Each motor has its own built-in motor drive that communicates directly with the hand unit and hand grips. This negates the need to mount a separate MDR to your rig, allowing for a more compact camera setup and a quicker setup time.
Simply set the motors and hand unit/hand grips to the same channel and you will have full control.
The motors allow for automatic calibration of the lens as well as manual calibration if you are using lenses that don’t have hard end stops at close focus and infinity.
The motors are designed to clamp onto 19mm or 15mm rods (with the included rod bushings). This clamp-on design allows you to easily attach and detach the motors without needing to remove any other accessory from your setup.
Every motor has a 0.8 mod, 35 tooth, 32 pitch gear attached, which is the standard gear size for cinema lenses. The torque of the Nucleus-M Motor at 14.8V is 2.5N·m
To power the motors, only one power port on your camera rig needs to be used. Simply plug the P-tap power cable into one of the motors and then daisy chain power to the rest of the motors with the short 7-pin to 7-pin cables.
The motors can be powered through a power source that has a voltage output ranging from 7.2V-24V.
The hand unit and hand grips are each powered with two 18650 rechargeable batteries (batteries NOT included). When fully charged, the batteries in the hand grips last up to 2 days, while in the hand unit they last up to 10 hours.
Remote start/stop is possible by plugging a compatible Nucleus-M R/S cable into the open 7-pin port of a motor. This then gives you R/S capabilities through the hand unit and/or the handles.
** PLEASE NOTE: The R/S cables we offer for our wooden handles ARE NOT compatible with the Nucleus-M since the engineering and pin configurations are completely different. Using the wooden handle R/S cables are not safe to use with the Nucleus-M.
Only use cables that have been developed by us exclusively for the Nucleus-M system.
Weight:
Motor Dimensions:
Material: Aluminum-alloy, stainless steel, ABS plastic, rubber, Brazilian rosewood
Color: Tilta Gray
Recommended Battery Link: https://tilta.com/support/which-batteries-do-you-recommend-for-the-g2-g2x/
Tiltamax Nucleus-M Firmware Update 18.12.19 – December 2018SKU: TIL-WLC-T03-K4 -
Lens control systems
Tilta Nucleus-Nano Micro USB to USB-C Nano Motor Power Cable
This Micro USB to USB-C cable for the Nucleus-Nano allows you to power the motor from a USB-C power output port.
This makes this cable the perfect solution for powering the motor from the DJI RS2.
This cable can also be used to power and control the Nano motor via our Advanced Side Handles.
Please Note: this cable cannot power the Nano motor from a camera body
SKU: TIL-WLC-T04-USBC -
Lens control systems
Tilta Photographic Lens Follow Focus Gear Ring(1x)
This follow focus adapter allows you to use your DSLR photo lens with any of the TILTA Follow Focus Systems. Simply tie the adapter down around the DSLR photo len’s focus wheel and now you can use the photo lens as a cine lens compatible with whichever follow focus system you desire.
(1) Photographic Lens Follow Focus Adapter
Color:
Black
Material:
Silicone Rubber
ABS plasticSKU: TIL-FR-T03 -
Camera rig attachments, brackets and components
Tilta PL Mount Adapter Support for RED V-RAPTOR V2
This bracket attaches to the front of the RED V-RAPTOR camera body to provide support for a PL Lens Mount Adapter.
This support attaches via multiple threads for increased security via four points of contact.
This accessory is the perfect solution for adding increased security to your PL Adapter, allowing you to support larger cinema lenses.SKU: TIL-ESR-T08-PL2 -
Camera rig attachments, brackets and components
Tilta Power Supply Base Plate for RS 2
The Power Supply Base Plate for DJI Ronin attaches directly to the base of the DJI RS2 or RS3 Pro and allows you to power the gimbal via Gold or V-Mount Batteries via the included P-tap to 2-pin cable.
The 1/4″-20 and 3/8″-16 threads on the bottom of the Base Plate allow you to mount the DJI Ronin to many different systems such as Tripods, Jibs, Sliders, Car Mounts, Stabilization Systems, and other products in our Ecosystem like the Hydra Alien and Float System.
The side bracket attaches from the Base Plate to the body of the DJI Ronin which provides an additional point of contact and added security.
This can be adapted to work with the DJI RS3 via our optional Security Bracket for DJI RS 3.SKU: TIL-TGA-PBP -
Camera rig attachments, brackets and components
Tilta Power Supply Module for DJI Video Transmitter – V Mount
Camera rig attachments, brackets and componentsTilta Power Supply Module for DJI Video Transmitter – V Mount
Designed for ergonomic and lightweight operation. Supports comfortable handling for longer period of time.
Full anti-slip silicone pad for comfortable handling.
Supports mounting to monitors with 1/4”-20 threads.
32mm adjustment range. Adjust the center of gravity for better handling.
Use the 1/4”-20 screws to connect the monitor and the battery plate. Provides added protection the battery mount and the monitor’s contact points.
Multiple built-in mounting points for various accessories. Easily accommodates efficient handheld setup.
Supports expansion Module for DJI Remote Monitor
This Power Supply Module is the perfect mounting and power solution for the DJI Video Transmitter.
The front and back plates of the module can be installed on both sides of the video transmitter.
The front side of the module allows you to mount your DJI Video Transmitter to a Gold/V-Mount Battery Plate on your camera system.
The back side then allows you to mount a Gold or V-Mount battery to the transmitter which can provide power to the transmitter as well as pass power through the module to the camera body.
This is a fantastic option for those who are looking for a clean and convenient way to mount and power the DJI transmitter.
NOTE: These Plate can only mount to the transmitter in one configuration which will position the SDI ports on the Operators side and the LCD Screen/Control Knob on the Assistant’s side.
V-Mount
1：Power Supply Module for DJI Video Transmitter – V Mount
2：3mm Hex Key (4.04.199-000000-031.00)*1Gold Mount
1：Power Supply Module for DJI Video Transmitter – Gold Mount
2：3mm Hex Key (4.04.199-000000-031.00)*1
Dimensions: 7 x 4.5 x 4 inches
Weight: 0.88 lbs
Materials: Aluminum-alloy, stainless steel
Color: BlackSKU: TIL-TGA-DVT-V
